BD9G101G
Step-down Switching Regulators with Built-in Power MOSFET

Internal high-side 42V Power MOSFET. It provides 0.5A DC output with small SOT23 package. Operating frequency is fixed 1.5MHz, allowing the use of small inductor and ceramic capacitor. Phase compensation components is built in. The BD9G101G is available in SOT-23-6(SSOP6) package.

Data Sheet Buy * Sample *
* This is a standard-grade product.
For Automotive usage, please contact Sales.

Product Detail

 
Part Number | BD9G101G-TR
Status | Recommended
Package | SSOP6
Unit Quantity | 3000
Minimum Package Quantity | 3000
Packing Type | Taping
RoHS | Yes

Specifications:

Grade

Standard

ch

1

Integrated FET / Controller

Integrated FET

Topology

Buck

Synchronous / Nonsynchronous

Non-synchronous

Vin1(Min.)[V]

6.0

Vin1(Max.)[V]

42.0

Vout1(Min.)[V]

1.0

Vout1(Max.)[V]

29.4

Iout1(Max.)[A]

0.5

SW frequency(Max.)[MHz]

1.7

EN

Yes

Operating Temperature (Min.)[°C]

-40

Operating Temperature (Max.)[°C]

105

Package Size [mm]

2.9x2.8 (t=1.25)

Features:

・ High and Wide Input Range (VCC=6V~42V)
・ 45V/800mΩ Internal Power MOSFET
・ 1.5MHz Fixed Operating Frequency
・ Feedback Pin Voltage 0.75V±1.5%
・ Internal compensated
・ Internal Over Current protection, Under Voltage Locked Out, Thermal shutdown
・ 0μA Shutdown Supply Current
・ 6-Lead SOT-23 package(SSOP6)

Evaluation
Board

 
    • Evaluation Board
    • BD9G101G-EVK-101
    • This evaluation board has been specifically developed to evaluate the BD9G101G non-synchronous buck DC/DC converter with integrated 45V/800mΩ power MOSFET. Features include wide input (6V to 42V) and output (1V to VCC x 0.7V) voltage ranges and a switching frequency of 1.5MHz.

  • User's Guide Buy

Design Resources

 

Documents

White Paper

  • Cutting-Edge Web Simulation Tool “ROHM Solution Simulator” Capable of Complete Circuit Verification of Power Devices and Driver ICs

User's Guide

  • Evaluation Board User's Guide

Reference Design

  • BD9G101G Reference Circuits and Bomlist

Technical Articles

Schematic Design & Verification

  • Buck DC/DC Converter Recommended Inductor List
  • Calculation of Power Dissipation in Switching Circuit
  • Considering Input Filter to Reduce Conducted Emissions by DCDC Converter
  • Considering Polarity of Power Inductor to Reduce Radiated Emission of DC-DC converter
  • Method for Monitoring Switching Waveform
  • PCB Layout Techniques of Buck Converter
  • Phase Compensation Design for Current Mode Buck Converter
  • Method for Determining Constants of
  • Power Supply Sequence Circuit with General Purpose Power Supply IC
  • Suppression Method of Switching Noise Using Linear Regulator and Low Pass Filter
  • Diode Selection Method for Asynchronous Converter
  • Measurement Method for Phase Margin with Frequency Response Analyzer (FRA)
  • Usage of SPICE Macromodel for DC/DC
  • Snubber Circuit for Buck Converter IC
  • Efficiency of Buck Converter
  • Calculation of Power Loss (Synchronous)
  • Inductor Calculation for Buck converter IC
  • Considerations for Power Inductors Used for Buck Converters
  • Capacitor Calculation for Buck converter IC
  • The Important Points of Multi-layer Ceramic Capacitor Used in Buck Converter circuit
  • Resistor Value Table to set Output Voltage of Buck Converter IC
  • Importance of Probe Calibration When Measuring Power: Deskew
  • Impedance Characteristics of Bypass Capacitor

Thermal Design

  • What Is Thermal Design
  • Basics of Thermal Resistance and Heat Dissipation
  • Method for Calculating Junction Temperature from Transient Thermal Resistance Data
  • Two-Resistor Model for Thermal Simulation
  • Notes for Temperature Measurement Using Thermocouples
  • Notes for Temperature Measurement Using Forward Voltage of PN Junction
  • Thermal Resistance
  • Precautions When Measuring the Rear of the Package with a Thermocouple

Tools

Calculation Tools

This Calculation Sheet supports the application circuit design of switching regulators. The sheet has formulas necessary for determining peripheral parts. You can easily determine the circuit parameters that meet the desired characteristics by setting the values according to the guidance.
  • Calculation-sheet for the circuit theoretical formula - BD9G101G

2D/3D/CAD

  • BD9G101G Footprint / Symbol
  • SSOP6 STEP Data
  • SSOP6 Footprint / Symbol

Packaging & Quality

Package Information

  • Package Information
  • Anti-Whisker formation

Manufacturing Data

  • Factory Information

Environmental Data

  • UL94 Flame Classifications of Mold Compound
  • Compliance with the ELV directive
  • REACH SVHC Non-use Declaration
  • RoHS Comission Delegated Directive

Export Information

  • The Export Control Order
  • Export Administration Regulations(EAR)